DISCONTINUED PRODUCT

Introduction

The vsm TTP10 has been designed as an alternative to the LBP series. In addition to touch-panel button operations, the TTP10 offers meter monitoring and the freedom of using virtual faders. The touch panel has been developed specifically for use with vsmStudio in OB vans and studios. The use of embedded components and an adapted embedded operating system guarantee a robust, maintenance-free and long-living system that meets the high requirements of mobile and stationary applications. High-quality materials and the innovative design of the panel give it both a robust and sophisticated appearance.

Features:

• Embedded system platform with adapted baseboard
• Atom N450 processor
• Capacitive touch behind a solid glass-surface
• IP54 frontally
• Small and comfortable aluminium-housing
• Foot and VESA 75 installation

Product Overview

vsmTTP10

Operating Conditions

This device is built to be used in a non-condensing environment within a temperature range of 0-50°C. Under or overshooting this working temperature range may cause fast aging of components or even malfunction of the whole device.

Spillage of any liquids e.g. coffee, coke, water... onto/into the device may cause damage.

The storage temperature of the device must be within -20°C to 60°C with a maximum of 75% non-condensing relative humidity at 60°C @ 0VDC supply-voltage.

DO NOT throw, drop or bend the unit and make sure that there is no strong permanent mechanical pressure on any side of the housing at any time.

Before installing or using this device, always read and observe the Important Safety Instructions.

Preparing for Operation

The TTP10 has an active write filter so it won't store any changes of the OS or the applications except for when the device receives a reset command via vsmDiscover. Due to this please apply all needed settings first and then use the "Reset" button in vsmDiscover to write the changes to the non-volatile memory. If the device loses power before a vsmDiscover reset command has been sent, it will also lose all changes that have been made since last start.

All Lawo vsm devices will be shipped with DHCP enabled network configuration. If you don't have a DHCP network ask your administrator for static network settings and edit the "Network" section if required.

Do the following settings in VSM Discover:

To connect the device to a vsmStudio, edit Server 1 – 4 and the Panel ID in the "Application" section.

The Location and Comment fields in the "Misc" section are to easily allocate the device in your environment.

Press "Apply" button if you are sure you have entered the settings correctly. Perform a reboot with the "Reset" button to store the configuration to the non-volatile memory.

Technical Specifications

Connectors

Power

Alternative connector (desktop panels only) for 12 V DC supply: 4-pin Hirose HR10A-7P-4P locked bayonet joint compact connector for better cable traction relief, mounted on power-supplies delivered with each vsmTTP10 panel.

	Pin	Signal
	1	GND
	2	GND
	3	+
	4	+

Power Supply

(EN) Warning

Important: It is understood that only the external Power-Supply-Unit (PSU) provided by Lawo, and shipped with the specific vsm device, is used for operating the product.

To feed the device via the DC input it is mandatory to use a 12V power source that is certified as “SELV/LPS” (if certified according to 60950) or as “ES1/PS2(LPS)” (if certified according to 62368) “NEC Class 2” 12V power source. The UL mark is valid only with use of UL certified PSUs of categories QQGQ (UL 60950) or QQJQ (UL 62368). The supplied Lawo 12V PSU is compliant to these requirements.

(F) Avertissement

Important: Il est entendu que seul le bloc d'alimentation externe fourni par Lawo, et livré avec le dispositif vsm spécifique, est utilisé pour faire fonctionner le produit.

Pour alimenter l'appareil via l'entrée DC, il est obligatoire d'utiliser une source d'alimentation 12V conforme aux exigences «SELV / LPS» (si certifiée selon la norme IEC 60950) ou «ES1 / PS2 (LPS)» (si certifiée selon la norme IEC 62368) Source d'alimentation 12V “NEC Classe 2”. La marque UL est seulement valable quand l'alimentation elle-même est certifiée par UL dans les catégories QQGQ (norme UL 60950) ou QQJQ (norme UL 62368).  Le bloc d’alimentation Lawo 12V fourni avec l’équipement est conforme à ces exigences.

Ethernet

Ethernet Communication Port to vsmStudio

(EN) Information

This interface is used as the ethernet communication port to vsmStudio.

Port de communication Ethernet vers vsmStudio

(F) Information

Cette interface est utilisée comme port de communication Ethernet vers vsmStudio.

Notice for Wiring:

• NC: no connection; do not connect to any signal or supply
• Only use shielded CAT5 (or higher standard) -specified networkable. Refer to TIA-568A or TIA-568B for wiring.
• Do not use cable-traces longer than 100m (328ft) between the device and network-switch for 100BASE-T communication.
• Make sure to keep to wiring standards and use shielded RJ45-plugs for shielded cable on both ends of the line.

(EN) Warning

It is mandatory, that copper based Ethernet connections (CAT 5, or higher standard RJ45) are led inside a building to the third party-device-ethernet-switch . If the Ethernet connection needs to be led outside a building it is mandatory to use a optical fiber. Use a converter to optical fiber and connect it in a short way (inside the building) to the device.

(F) Avertissement

Il est obligatoire que les connexions Ethernet à base de cuivre (CAT 5 ou une norme supérieure, RJ45) soient installées à l'intérieur d'un bâtiment jusqu'au prochain switch Ethernet. Si la connexion Ethernet doit être dirigée à l'extérieur d'un bâtiment, utilisez un convertisseur en fibre optique et une connexion courte (à l'intérieur du bâtiment) à l'appareil.